“Communication was excellent from my 1st contact with Moe to the completion of the work. This included follow-up messages…”
Christine M. · Glasgow
Google review
A lot of housing from the sixties and seventies was plumbed in microbore, the thin eight or ten millimetre heating pipe that runs from a manifold out to each radiator. It was quick to install and it works. What it does not tolerate is a dirty system, because there is very little room in there before the flow starts to suffer.
Tell us what's up, we usually get back within the hour with a clear price.
Erskine is largely a sixties and seventies estate town, which means a good share of the heating here was piped in a way modern installers rarely use.
The layout is worth understanding because it changes how a fault behaves. Instead of one main circuit with radiators teed off it, each radiator has its own pair of small pipes running back to a central distribution point, usually under a floor or in an airing cupboard. That means a problem on one run affects that radiator and nothing else, which is genuinely useful for diagnosis. It also means finding the manifold is the first practical step in almost any work on the system, and in a house where nobody has needed it for thirty years that can take a while.
That produces a fault that looks worse than it is. One radiator goes cold, everything else is fine, and the householder is told the pipework is obsolete and the house needs replumbing. Sometimes that is true. Far more often it is one run, and one run can be cleared or replaced on its own for a fraction of a system. Plumbers who have not worked on much microbore tend to reach for the bigger answer. Mo, Muhammad and David are all Gas Safe registered and cover heating.
Erskine is close in on the Renfrewshire round so booked work usually gets a choice of days.
Out of hours Matt takes the callouts. On a system that has lost most of its heat rather than one radiator, say so, because that is a different fault. Call 07988 591331.
Gas and heating is Mo, Muhammad or David, all Gas Safe registered. Fitting a new boiler to microbore is perfectly normal and worth doing with the system cleaned rather than as it stands.
Paul leads the drain team and Kyle runs the jetting, across the estate housing here.
Microbore work, system cleaning and protection. We would rather clear a run than condemn a system that has fifty years of service in it already.
In microbore a small amount of debris blocks a lot of the pipe. A single dead radiator with everything else fine is often the pipe rather than the radiator or its valve.
The same amount of sludge that a modern 15mm system tolerates will noticeably restrict an 8mm run, so cleanliness matters more here than in most housing.
The runs radiate from a central point, often under a floor or in an airing cupboard, and work becomes far easier once somebody has located it.
Microbore is not defective and plenty of it is working perfectly after fifty years. Replacing a whole system when one run is blocked is an expensive answer to a smaller question.
A house here had one bedroom radiator that had been cold for three winters and a quote for replumbing the whole heating system. The run to it was blocked a short distance from the manifold. Clearing that one length brought the radiator back and the rest of the system, which had been working perfectly the whole time, was left alone. It got a filter and inhibitor at the same visit so the same thing is less likely again.
We give you a clear price before any work starts and that price is what goes on the invoice. Where one run is the problem we will quote for that run, and we will say plainly if we think the wider system genuinely does need doing.
Do not replace it on principle. Microbore that is flowing and clean will keep working, and there is nothing inherently wrong with it. What decides the question is how much of it is restricted and why. If one radiator is dead and the rest are fine, that is one run, and it can usually be cleared or replaced on its own for a fraction of a system. If several are struggling and the water coming out is black, the system is dirty and the answer is cleaning it properly and then protecting it with a filter and inhibitor, because the same thing will happen again otherwise. If runs keep blocking after a proper clean, that is when replacing pipework becomes the honest recommendation rather than the first suggestion. The one thing worth doing regardless is protecting it. Microbore has less margin than modern pipe sizes, so a magnetic filter and inhibitor earn their keep here more than almost anywhere else.
250+ five-star reviews across Google, Trustpilot and Facebook, from real Glasgow customers.
“Communication was excellent from my 1st contact with Moe to the completion of the work. This included follow-up messages…”
Christine M. · Glasgow
Google review
“Our radiator pipe was bent and leaking. They answered straight away… Guy was here an hour later and he was wearing ID, very professional, patient and kind. We just got a new carpet in this room and he done an amazing job on getting little to no water on it. Couldn't recommend enough, price was reasonable.”
Kayleigh A. · Glasgow
Google review
“We lost heating just in time for the coldest day of the year with a baby in the house… When I contacted them they were ready to dispatch that night. Fixed by the afternoon. Quoted that morning and no extra charges were added. Honestly cannot thank them enough.”
Jemma M. · Glasgow
Google review
“As a small business owner, I needed a drainage company that could respond quickly. The team attended first thing in the morning, cleared the blocked drain and carried out a full CCTV survey. All documentation emailed across promptly. Professional, efficient and great value for money.”
Eric V. · Glasgow
Google review
25 years, 10,000+ jobs, £5m insured, call or WhatsApp, day or night. Clear price, tidy job, guaranteed.